Skip to main content

primosplint

light cured composite splint material

in general light cured composite is the most precise, distortion-free and antiallergenic material for night guards and more. More info...

 

primosplint Start Set
plus statutory VAT and shipping costs
$229.00

the kit includes:

  • PS100, pack of 12 primosplint strands
  • PS202, primostick, bonder
  • PS203, primosep, gypsum insulation
  • PS204 primoglaze, gloss finish
  • PS205, primoclean cleaning fluid
  • IM200 metatouch, hand isolation
  • Instructions for use

uses

  • function therapy bite splints
  • night guards
  • verification indexes
  • insertion guides
  • transfer jigs

advantages

  • very quick and easy to work with
  • modelling playdough like consistency at room temperature – no heat needed
  • cures reliably in most conventional light curing units
  • extremely precise, no noticeable shrinkage, expansion or distortion
  • abrasion-optimized, protects the tooth structure and the TMJ
  • MMA and peroxide free – lowest allergic potential for technician and patient
  • fully autoclavable – no distortion during steam sterilisation
  • can be easily bonded to other materials (PMMA-acrylic or suck down matrix)
  • no taste or smell and easy to repair

case pictures

advice for allergy patients

The bite splint material primosplint has been specially developed with regard to the lowest possible allergy potential.

When manufacturing bite splints for allergy patients, the practitioner should avoid using peripheral products such as glaze lacquers, bonding and insulating materials, cleaning liquids as well as, depending on the manufacturer, suck-down matrixes, since these auxiliary materials might have a higher allergy potential.

A complete curing of the primosplint material in a suitable light curing device (350-400nm) must be ensured. UV hand-held lights are not suitable.

We regularly receive inquiries as to whether primosplint contains substances that can cause intolerance, hypersensitivity reactions or unwanted side effects.

The most frequent inquiries relate to the following substances. All listed substances are not contained in primosplint.


primosplint PS100 is free of:


2-Hydroxyethylmethacrylat (HEMA)
Benzoylperoxid
BIS-GMA
Bisphenol
BPA
Colophony
Dibenzoyl peroxide
Dipentamethylenthiuramdisulfid
Dithiobis-(dimethylthiocarboxamid)
Ethylendiamin
Ethylenglycoldimethacrylat (EGDMA)
Eugenol
Hydroxychiolin
Kaliumdicyanoaurat
Melamin-Formaldehydharz
Menthol
Methyl hydrochinon
Methylmethacrylat (MMA)
N,N-Dimethyl-p-toluidin
Natriumthiosulfatoaurat
Neopren
Nickel (II)-Sulfat
N-Isopropyl-N‘-phenyl-p-phenylendiamin
Palladiumchlorid
Peroxid
Peru balsam
Phenylendiamine and their derivates
Phthalaten
Radioopaque substances
Tetraethylthiuramdisulfid (Disulfiram)
Tetramethylhiurammonodisulfid
Tetramethylhiurammonosulfid
Thiomersal
Thiuram-Mix
Triethylenglycol dimethacrylat (TEGDMA)
Softeners
Wool wax alcohol


If you have any questions about further substances, please do not hesitate to contact us!

Tel.: +1 / 203 / 682.6429
E-mail: info@primotecusa.com

  • function therapy bite splints
  • night guards
  • verification indexes
  • insertion guides
  • transfer jigs

  • very quick and easy to work with
  • modelling playdough like consistency at room temperature – no heat needed
  • cures reliably in most conventional light curing units
  • extremely precise, no noticeable shrinkage, expansion or distortion
  • abrasion-optimized, protects the tooth structure and the TMJ
  • MMA and peroxide free – lowest allergic potential for technician and patient
  • fully autoclavable – no distortion during steam sterilisation
  • can be easily bonded to other materials (PMMA-acrylic or suck down matrix)
  • no taste or smell and easy to repair

The bite splint material primosplint has been specially developed with regard to the lowest possible allergy potential.

When manufacturing bite splints for allergy patients, the practitioner should avoid using peripheral products such as glaze lacquers, bonding and insulating materials, cleaning liquids as well as, depending on the manufacturer, suck-down matrixes, since these auxiliary materials might have a higher allergy potential.

A complete curing of the primosplint material in a suitable light curing device (350-400nm) must be ensured. UV hand-held lights are not suitable.

We regularly receive inquiries as to whether primosplint contains substances that can cause intolerance, hypersensitivity reactions or unwanted side effects.

The most frequent inquiries relate to the following substances. All listed substances are not contained in primosplint.


primosplint PS100 is free of:


2-Hydroxyethylmethacrylat (HEMA)
Benzoylperoxid
BIS-GMA
Bisphenol
BPA
Colophony
Dibenzoyl peroxide
Dipentamethylenthiuramdisulfid
Dithiobis-(dimethylthiocarboxamid)
Ethylendiamin
Ethylenglycoldimethacrylat (EGDMA)
Eugenol
Hydroxychiolin
Kaliumdicyanoaurat
Melamin-Formaldehydharz
Menthol
Methyl hydrochinon
Methylmethacrylat (MMA)
N,N-Dimethyl-p-toluidin
Natriumthiosulfatoaurat
Neopren
Nickel (II)-Sulfat
N-Isopropyl-N‘-phenyl-p-phenylendiamin
Palladiumchlorid
Peroxid
Peru balsam
Phenylendiamine and their derivates
Phthalaten
Radioopaque substances
Tetraethylthiuramdisulfid (Disulfiram)
Tetramethylhiurammonodisulfid
Tetramethylhiurammonosulfid
Thiomersal
Thiuram-Mix
Triethylenglycol dimethacrylat (TEGDMA)
Softeners
Wool wax alcohol


If you have any questions about further substances, please do not hesitate to contact us!

Tel.: +1 / 203 / 682.6429
E-mail: info@primotecusa.com

technical tipsuseful tips for your workflow

When opening a new stick of primosplint gently knead it for about 10 to 15 seconds to soften up the material. This will make the material softer and easier to work with.

For maximum clarity lightly sandblast the finished splint (approx. 110 micron aluminium oxide, 30 PSI) inside and outside. Then apply one thin layer of primoglaze on the inside, blow off any access and apply two thin layers on the outside. Light cure according to the instructions.

If adding Primosplint to a suck down matrix, make sure that the surface is roughened well enough before applying primostick bonder.

Do not use strong strobe lights for curing.

working procedurethe workflows for standard applications

backgrounduseful background information

Primosplint is a thixotropic material, meaning the more energy put into it, the softer and more pliable it gets.

Primosplint provides the highest strength without any brittleness because tensile strength and modulus of elasticity have been optimized for bite splint applications.

Splints made of primosplint have a very high accuracy of fit, meaning they are utmost dimensionally stable during and after polymerization. This prevents "rocking" or "seesawing" effects.

The mechanical properties of primosplint have been carefully tuned to relieve the temporomandibular joint and protect the tooth structure. With a flexural strength of > 70 MPa and a modulus of elasticity of > 1500 MPa, bite splints made of primosplint meet the mechanical requirements asked for by modern splint therapy.

When opening a new stick of primosplint gently knead it for about 10 to 15 seconds to soften up the material. This will make the material softer and easier to work with.

For maximum clarity lightly sandblast the finished splint (approx. 110 micron aluminium oxide, 30 PSI) inside and outside. Then apply one thin layer of primoglaze on the inside, blow off any access and apply two thin layers on the outside. Light cure according to the instructions.

If adding Primosplint to a suck down matrix, make sure that the surface is roughened well enough before applying primostick bonder.

Do not use strong strobe lights for curing.

Primosplint is a thixotropic material, meaning the more energy put into it, the softer and more pliable it gets.

Primosplint provides the highest strength without any brittleness because tensile strength and modulus of elasticity have been optimized for bite splint applications.

Splints made of primosplint have a very high accuracy of fit, meaning they are utmost dimensionally stable during and after polymerization. This prevents "rocking" or "seesawing" effects.

The mechanical properties of primosplint have been carefully tuned to relieve the temporomandibular joint and protect the tooth structure. With a flexural strength of > 70 MPa and a modulus of elasticity of > 1500 MPa, bite splints made of primosplint meet the mechanical requirements asked for by modern splint therapy.

bestseller

primosplint bestseller

all products

all primosplint products

primosplint-KIT1

Bild
primosplint-KIT1
x

the kit includes:

  • PS100, pack of 12 primosplint strands
  • PS202, primostick, bonder
  • PS203, primosep, gypsum insulation
  • PS204 primoglaze, gloss finish
  • PS205, primoclean cleaning fluid
  • IM200 metatouch, hand isolation
  • Instructions for use
item no.:
PS-KIT1
Price
$229.00

primosplint bitesplint material (12 pcs/box)

Bild
primosplint Aufbissschienen (12 Stränge)
x

light-curing composite material
Pack of 12 strands of 8.3g each,
seperatly packaged

item no.:
PS100
Price
$119.00

primostick (bonder 10ml)

Bild
primostick (Bonder 10ml)
x

light-curing bonder 10ml bottle

item no.:
PS202
Price
$24.50

primosep (stone and die separator 50ml)

Bild
primosep (Gipsisolierung 50ml)
x

Gypsum Insulation 50ml bottle

item no.:
PS203
Price
$19.00

primoglaze (glaze lacquer 10ml)

Bild
primoglaze (Glanzlack 10ml)
x

light-curing gloss varnish 10ml bottle

item no.:
PS204
Price
$26.00

primoclean (cleaning liquid 50ml)

Bild
primoclean (Reinigungsflüssigkeit 50ml)
x

Cleaning fluid 50ml bottle

item no.:
PS205
Price
$19.50

Metatouch finger and instrument separator

Bild
Metatouch Handisolierung
x

(43gr.)

item no.:
IM200
Price
$35.00

primosplint bestseller

primosplint bitesplint material (12 pcs/box)

Bild
primosplint Aufbissschienen (12 Stränge)
x

light-curing composite material
Pack of 12 strands of 8.3g each,
seperatly packaged

item no.:
PS100
Price
$119.00

primostick (bonder 10ml)

Bild
primostick (Bonder 10ml)
x

light-curing bonder 10ml bottle

item no.:
PS202
Price
$24.50

primosep (stone and die separator 50ml)

Bild
primosep (Gipsisolierung 50ml)
x

Gypsum Insulation 50ml bottle

item no.:
PS203
Price
$19.00

primoglaze (glaze lacquer 10ml)

Bild
primoglaze (Glanzlack 10ml)
x

light-curing gloss varnish 10ml bottle

item no.:
PS204
Price
$26.00

all primosplint products

primosplint-KIT1

Bild
primosplint-KIT1
x

the kit includes:

  • PS100, pack of 12 primosplint strands
  • PS202, primostick, bonder
  • PS203, primosep, gypsum insulation
  • PS204 primoglaze, gloss finish
  • PS205, primoclean cleaning fluid
  • IM200 metatouch, hand isolation
  • Instructions for use
item no.:
PS-KIT1
Price
$229.00

primosplint bitesplint material (12 pcs/box)

Bild
primosplint Aufbissschienen (12 Stränge)
x

light-curing composite material
Pack of 12 strands of 8.3g each,
seperatly packaged

item no.:
PS100
Price
$119.00

primostick (bonder 10ml)

Bild
primostick (Bonder 10ml)
x

light-curing bonder 10ml bottle

item no.:
PS202
Price
$24.50

primosep (stone and die separator 50ml)

Bild
primosep (Gipsisolierung 50ml)
x

Gypsum Insulation 50ml bottle

item no.:
PS203
Price
$19.00

primoglaze (glaze lacquer 10ml)

Bild
primoglaze (Glanzlack 10ml)
x

light-curing gloss varnish 10ml bottle

item no.:
PS204
Price
$26.00

primoclean (cleaning liquid 50ml)

Bild
primoclean (Reinigungsflüssigkeit 50ml)
x

Cleaning fluid 50ml bottle

item no.:
PS205
Price
$19.50

Metatouch finger and instrument separator

Bild
Metatouch Handisolierung
x

(43gr.)

item no.:
IM200
Price
$35.00

All products

primosplint-KIT1

Bild
primosplint-KIT1
x

the kit includes:

  • PS100, pack of 12 primosplint strands
  • PS202, primostick, bonder
  • PS203, primosep, gypsum insulation
  • PS204 primoglaze, gloss finish
  • PS205, primoclean cleaning fluid
  • IM200 metatouch, hand isolation
  • Instructions for use
item no.:
PS-KIT1
Price
$229.00

primosplint bitesplint material (12 pcs/box)

Bild
primosplint Aufbissschienen (12 Stränge)
x

light-curing composite material
Pack of 12 strands of 8.3g each,
seperatly packaged

item no.:
PS100
Price
$119.00

primostick (bonder 10ml)

Bild
primostick (Bonder 10ml)
x

light-curing bonder 10ml bottle

item no.:
PS202
Price
$24.50

primosep (stone and die separator 50ml)

Bild
primosep (Gipsisolierung 50ml)
x

Gypsum Insulation 50ml bottle

item no.:
PS203
Price
$19.00

primoglaze (glaze lacquer 10ml)

Bild
primoglaze (Glanzlack 10ml)
x

light-curing gloss varnish 10ml bottle

item no.:
PS204
Price
$26.00

primoclean (cleaning liquid 50ml)

Bild
primoclean (Reinigungsflüssigkeit 50ml)
x

Cleaning fluid 50ml bottle

item no.:
PS205
Price
$19.50

Metatouch finger and instrument separator

Bild
Metatouch Handisolierung
x

(43gr.)

item no.:
IM200
Price
$35.00